Recently bought a unit for drying clothes? So connecting a tumble dryer is a hot issue for you. Here you should pay attention to the 4 most important points: alignment, power, drain and ventilation. Following the simple recommendations and instructions given in the article, you can connect the device correctly without any problems, because the process itself is quite simple and understandable for the average user.
Installation options for dryers
Today on the domestic market there are three main types of clothes dryers:
- Condensation. They allow heated air to pass through the laundry chamber. Excess moisture from the drum through a heat exchanger enters a special assembly container, which is recommended to be cleaned after each use.
- Exhaust. They provide drying of things by venting air into the ventilation duct.
- With a heat pump. They have the principle of operation similar to condensation dryers. The main difference is that condensate does not accumulate in the tray, but immediately goes into the sewer.
Important! Condensation models are suitable for rooms where there is no air exhaust. In private houses and apartments with a normal ventilation system, it is preferable to install exhaust devices or models with a heat pump.
The best solution for a small apartment will be a unit that simultaneously performs the functions of a washing and drying machine.
The most popular manufacturers of dryers with a proven track record are Miele, Siemens, AEG, Electrolux, Indesit, Bosch. They are distinguished by good power, long service life and reliability. On the drying devices of these companies, experts recommend stopping your choice.
Dryer placement options
There are many ways to install a drying machine. Most popular:
- integrating under the kitchen worktop;
- vertically above an already installed washer;
- in a special drywall niche;
- near the washer (but already in the horizontal plane).
Important! In small-sized apartments, it is preferable to place the drying device on top of the washing machine to save space.
Necessary tools
Getting started, stock up:
- straight or Phillips screwdriver;
- building level;
- pliers
- drying hose;
- clamp.
How to connect a machine
The sequence of actions will be determined by the installation method.
When placed vertically
In most cases, the dryer is installed in a vertical column with a washer. To do this, it is recommended to choose models of the same width. In this case, the entire construction of the equipment will be more stable.
Before starting the installation, you must buy fasteners with special caps (adapter frames).
Action Scheme:
- Install the fasteners on the lower unit (washer).
- Unscrew the legs on the dryer and install it in the caps.
- Level the equipment using the building level. To do this, lay it first on the front of the machine (the edges should point to the left and right side, respectively), then on the back, then on the sides, adjust the height and level of the tilt.
When placed horizontally
This installation method will ensure maximum stability of the equipment. To install in the right place, you just need to unscrew the legs to the desired length and carry out leveling.
Connection to communications
After installation is complete, you can proceed to the electrical connection. Then, depending on the type of device - to the connection of the sewer or ventilation.
We connect to the power supply
Guide to action:
- Withdraw from the junction box a special line for household appliances.
- Use only a grounded power outlet to turn it on to prevent electric shock.
- Provide a circuit breaker for the unit. In the event of a power surge, he will save the machine from damage.
- Plug the dryer into a power outlet.
Important! Before starting the first connection of the machine to the network, turn off the electricity in the house for the safety of electrical work.
Instructions for connecting the ventilation
- Bring a flexible hose to the air vent of the machine to exhaust air (supplied with any type of dryer) and secure with a previously prepared clamp. Do this with a screwdriver and pliers, tightening the clamp quite tightly so that when pulling it does not fly off.
- Take the other end of the duct into the ventilation shaft in the wall. Withdraw so that there are no excesses on the corrugation or their number is minimal. Is the hose hanging loose? Also secure it with a clamp.
- Turn on the dryer and run a test run. Make sure the device is working properly.
Connection to the sewage system is even easier: the drain hole of the hose simply connects to the sewer system.
Now you know how to connect a drying machine without assistance and save on calling a wizard. The process itself is very similar to connecting a washer. Correct installation and connection is a guarantee of a long and trouble-free operation of the equipment.