Is there an error on the Korting dishwasher display? Has the technique stopped working, beeping and blinking? So she tries to inform you of a problem in the system.
The electronic module controls all parts and components in the car. As soon as a breakdown occurs, it issues an error code on the display so that you can find and fix the problem as quickly as possible. Decoding of all the icons below.
PMM Korting Error Codes
If you notice them on the screen, first rule out a system failure. To do this, try to reset the error:
unplug the PMM plug from the outlet;
wait 10-15 minutes;
restart the launch.
If the code no longer appears on the display, you have managed to eliminate the cause of its appearance. But if it is on again, decrypt its value according to the table and try to fix the problem.
Error code
Value
Reasons for the appearance
How to fix the situation
E1
There were problems with water intake. Timed out.
There is no water in the system.
Stopcock closed.
The equipment is not connected correctly.
Faulty solenoid valve.
Inlet filter clogged.
The level sensor is broken or gives incorrect readings.
Blown wiring.
The electronic board is out of order.
What should be done:
Check for water in the system. Wait for it to appear.
Turn the shut-off valve, it may have been shut off.
Refer to the connection diagram for the dishwasher in the instructions. Make sure the hoses are connected correctly.
Diagnose the intake valve: apply voltage to it. Check the electronic part with a multimeter. If broken, replace the valve.
Clean the inlet filter from dirt. To do this, disconnect the hose from the body, remove the filter and rinse under the tap.
Inspect the level sensor, measure the contact resistance with a multimeter. The pressure switch cannot be repaired, only replaced.
Inspect the internal wiring in sequence. Replace burnt elements or cables.
Repair of the control board and accurate diagnostics are best left to a specialist.
E2
Water does not drain.
Why PMM "Curting" may show an error:
the drain hose is twisted, pinched or clogged with debris;
drainage filter clogged with food debris, small debris, napkins;
the impeller of the pump is blocked;
defective drain pump;
the pressure switch is unsuitable for use;
the control module does not work correctly: the triac burned out or it completely failed.
How to fix the problem:
Unscrew the drain hose. Rinse it under the pressure of water. Make sure that it is level, without excesses.
Open the hopper door. Unscrew the drain filter in the pan. Clean the part with a detergent brush, rinse under the tap.
Remove the pump cover, inspect the impeller, and remove foreign objects. To get to the pump, disassemble the dishwasher. Check the part for clogging; check the electronics with a multimeter.
Diagnose and replace the pressure switch.
Inspect the board. If burnt parts are visible on it, contact the master. He will restore her work.
E4
Overflow. Water in the PMM pan.
What happened:
a leak occurred in the car: water got into the sump where the float sensor worked;
Aquastop protection is out of order.
What to do:
1. Inspect the hopper of the dishwasher, look for leaks. Check connections of hoses and fittings. Make sure that they do not bend or lose tightness. Also inspect the rubber seal on the door. Faulty elements replace.
2. Diagnose the Aquastop sensor. It can be located at the bottom of the machine. Mechanical protection is part of the inlet hose. Therefore, if it leaks, replace the hose completely.
E8
Damage to the flow sensor.
What is the cause of the malfunction:
the sensor has failed;
the wiring from the module to the sensor burned out, the connections were broken;
the control module burned out.
DIY repair:
Check and replace flow sensor.
Diagnostics of wiring, connections. In case of violation of insulation, the presence of burnt parts, a new loop is installed.
The module is checked and replaced in the event of a malfunction.
Now you know what to do when an error occurs in the Curter dishwasher. Follow operating instructions to avoid premature breakdowns.
Contents: hide Advantages Design features Varieties Power Operating principle Cutting element Model overview Bosch Makita Festool "Fiolent" "Interskol" Wood, some other materials are processed using a manual milling machine. The tool is similar to stationary ...